What If What if The scanner is not Refer to page Connecting the decoding and the green Scanner on page to verify that LED is not lit? Page 40 Scan Pattern line, 5-direction dynamic cross pattern Decode Depth of Maximum working distance is 8 in. Field Page Chapter 4. Programming Chapter 4 Programming Defaults The LS is shipped with the default settings listed on the next few pages. These default values are stored in non-volatile memory Flash and are preserved even when the scanner is powered down.
You can change these default values by scanning the appropriate bar codes included in this manual. Page 44 Programming Table Page 46 Programming Table Page 48 Programming Audible Feedback During the programming process the LS scanner will emit a series of beep tones and sequences to help you determine if you are proceeding correctly.
The chart below defines all possible tones and sequences. Table Beeper Definitions Page Chapter 5. Parameters Chapter 5 Parameters Set Default Parameter Scanning this bar code returns all parameters to the values listed Defaults on page The scanner's baud rate setting should match the data rate setting of the host device. If not, data may not reach the host device or may reach it in distorted form.
To select a baud rate, scan one of the following bar codes. Select the parity type according to host device requirements. If you select ODD parity, the parity bit has a value 0 or 1, based on data, to ensure than an odd number of 1 bits are contained in the coded character. MARK SPACE NONE Page 76 Parameters If this communications sequence fails, the scanner issues an error indication.
In this case, the data is lost and must be rescanned. Note: The DTR signal is jumpered active. The scanner deasserts RTS when the transmission is complete.
However, the scanner waits for CTS to be asserted before transmitting data. If CTS is not asserted within two seconds, the scanner issues an error indication and discards the data. The scanner waits up to two seconds for CTS to be asserted. If CTS is not asserted during this time, the scanner issues an error indication and discards the data.
There are five options. None When this option is selected, data is transmitted immediately. After three unsuccessful attempts to send data when NAKs are received, the scanner issues an error indication and discards the data.
If an ENQ is not received within two seconds, the scanner issues an error indication and discards the data. The host must transmit an ENQ character at least every two seconds to prevent transmission errors. When the scanner has data to send, it then waits for an XON character before transmission. The delay period can range from 0. Page Stop Bit Select Rs LS Product Reference Guide Stop Bit Select RS The stop bit s at the end of each transmitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial data stream.
An autodiscriminate option is also available. To enable this code type: Scan the bar code below. The default setting is Any Length. The length of a code refers to the number of characters i. Page Parameters T wo Discrete Lengths This option allows you to decode only those codes containing two selected lengths. For example, if you select Code 39 Two Discrete Lengths, then scan 0, 2, 1, 4, only Code 39 symbols containing 2 or 14 characters are decoded.
Numeric Bar Codes begin on page For example to decode Code 39 symbols containing between 4 and 12 characters, first scan Code 39 Length Within Range. Page Any Length Parameters Any Length Scanning this option allows you to decode Code 39 symbols containing any number of characters.
Note: Selecting this option disables Code 39 Decode Performance. Page Code 39 Check Digit Verification Code 39 Check Digit Verification When enabled, this parameter checks the integrity of a Code 39 symbol to ensure it complies with specified algorithms.
Only those code 39 symbols which include a modulo 43 check digit are decoded when this parameter is enabled. When enabled, the ASCII character set assigns a code to letters, punctuation marks, numerals, and most control keystrokes on the keyboard. Page Set Lengths For Interleaved 2 Of 5 Parameters Set Lengths for Interleaved 2 of 5 Lengths for I 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range.
For example to decode I 2 of 5 symbols containing between 4 and 12 characters, first scan I 2 of 5 Length Within Range. For example, if you select I 2 of 5 One Discrete Length, then scan 1, 4, the only I 2 of 5 symbols decoded are those containing 14 characters. For example, if you select I 2 of 5 Two Discrete Lengths, then scan 0, 2, 1, 4, the only I 2 of 5 symbols decoded are those containing 2 or 14 characters. Any Length Scanning this option allows you to decode Codabar symbols containing any number of characters.
You can learn more about the cookies we use as well as how you can change your cookie settings by clicking here. By continuing to use this site without changing your settings, you are agreeing to our use of cookies. Visit the Support Community for access to Zebra's complete knowledge base.
Accept and Continue. Login Register. My Zebra Register Logout. Zebra Blog. Support and Downloads. Scanner Firmware Update Notification. Here are support and repair resources for your Barcode Scanner. Warranty Check.
Request a Repair. Email Us. Contact Support. Videos -No Selection- English. Scroll For More Videos. Knowledge Articles. Search Knowledge Base. This is going to be the key to determining how this scanner works. If it is a USB scanner, then it could be that it is something that works as a keyboard wedge which will work with RetailEdge or not. If you find out that this cable is a standard USB Keyboard Wedge cable, then you probably just need to configure the scanner properly.
To see if the scanner will work with RetailEdge, just open a program like Notepad, and then scan the barcode. If you see the full value of the barcode usually found as the human readable number below a UPC , followed by a carriage return, then this device will work fine with RetailEdge. Who is online Users browsing this forum: No registered users and 1 guest.
Board index All times are UTC.
0コメント